Cleaning paving stones: valuable tips for clean paths

Simple ways to tackle everyday dirt – we'll show you how to clean your garden and everything around the house effectively.


Overview: cleaning paving 

  • The pressure washers are the most effective way to clean paths
  • Start with low water pressure and test on a hidden spot whether the stones are suitable for pressure washers
  • Use the surface cleaner for concrete and hard-stone paving, and lukewarm water, a soft brush and a pH-neutral cleaner for soft, porous natural stone
  • For environmental reasons, use biodegradable cleaning agents such as the STIHL CS 100 stone and façade cleaner and follow local regulations on waste water
  • Other options: neutral soft soap or, for concrete stones, a soda and water mixture, using safety glasses

Cleaning paving: pressure washers

Pressure washers are an effective way of removing dirt and weeds from your paths. The high water pressure loosens even the most stubborn dirt and cleans every stone quickly and thoroughly. Pressure washers are especially effective on large areas: the job is done quickly and without effort.

A few general tips to bear in mind when working with pressure washers:

  • Not all paved surfaces may be cleaned with a pressure washer. Concrete and hard-stone paving can be cleaned with low water pressure, e.g. with a surface cleaner. Test first on an inconspicuous area to see how the stones react and whether they are suitable for cleaning with a pressure washer.
  • The surface cleaner works particularly gently and without splashing, so the surrounding area stays clean while you work. When using the flat-jet nozzle, make sure there is enough distance between the nozzle and the paving.
  • Do not work in the rain or in wet conditions.

Cleaning paving: instructions

1. Remove coarse dirt

Cleaning paved paths: legal requirements

The water used to clean paving can contain chemicals, acids and other harmful substances. These must not reach the sewer system or the groundwater. Regulations can vary from region to region, and breaches may result in fines. 

Before cleaning paved paths, you should check the applicable regulations with your local authority.

Cleaning paving: household remedies

If you don't have stone and façade cleaner to hand, you can use simple household remedies. For cleaning small areas, hot water, a soft brush and neutral soft soap are enough. Soda is also a tried-and-tested remedy for dirt. Household products mixed by the user must not be put into pressure washers. The pressure washer should only be filled with a suitable cleaning agent.

Cleaning paving with soda

A mixture of soda and water is an effective but strongly alkaline cleaning agent. It can be used on particularly dirty concrete stones. Always wear safety glasses while working, as soda can irritate the eyes. And don't forget your work gloves.

  • The amount of mixture you need depends on the area you want to clean. As a rule, use 10 grams of soda for every 1 litre of water. Spread the mixture over the paving stones with a sponge broom and leave it to work for around 5 to 6 hours. Rinse off the solution with clean water from the pressure washer or the garden hose, following local regulations on waste water.

Not recommended: cleaning paving with vinegar

Vinegar is a popular household product for cleaning all kinds of surfaces. However, it is not suitable for cleaning stone, for the following reasons:

  • Acetic acid attacks the joints between the stones and can therefore destabilise the bedding of the paving stones.
  • Vinegar leaves pale stains and should not come into contact with calcareous stones. This means you should not use vinegar to clean concrete paving or natural stone.
  • Acetic acid irritates the respiratory system and mucous membranes, so if it is used incorrectly or splashes, there is a risk of chemical burns.

Cleaning paving: what to consider with concrete and natural stone

How you clean your paving depends on what it is made of. So before cleaning, check what material the paths in your garden are made from.

Basically, a distinction is made between concrete stones and natural stones.

Cleaning concrete stones

Concrete stones are the classic type of paving and are available in a variety of shapes. Manufactured stones can be cleaned with a surface cleaner. To check how well the stone surface copes, start with low water pressure and increase it as required.

Concrete stones are resistant to neutral and alkaline cleaning agents. However, they are made with acid-sensitive limestone and can be damaged when cleaned with acidic products.


STIHL tip

A natural phenomenon that many people find annoying is white staining on concrete paving: efflorescence. It is typical of newly laid stones and is nothing more than excess salt dissolved out of the concrete by rain and moisture. The stains can be removed very easily and in an environmentally friendly way – with a broom, water and, if necessary, a neutral cleaning agent. 

Cleaning natural stone

Natural stone paving made of granite, marble, sandstone or basalt is elegant and of particularly high quality. To keep natural stone looking beautiful, use only pH-neutral cleaning agents. Acids and surfactants, on the other hand, damage the natural material.

Pressure washers clean hard-stone paving such as granite, basalt and quartzite most effectively. This stone is durable and withstands high water pressure. You can also clean clay brick paths with a pressure washer.

Softer materials call for gentler methods: with lukewarm water, a soft brush and a neutral cleaning agent, you are always on the safe side.